Chimney Cap & Crown in Boulder - Measured and Fitted, One Price

Trusted Chimney Cap & Crown for Boulder Homeowners

Our Chimney Cap & Crown cost guide shows Boulder repairs typically run $280-$1,850 depending on whether you need a standard cap installation, crown coating, or full rebuild after freeze-thaw damage. Most cap replacements and crown repairs are completed in a single visit, with custom or multi-flue caps fabricated and installed within 3-5 business days. Call (970) 598-0453 for a written estimate before any work begins.

Call (970) 598-0453

We’ve completed more than 38,000 chimney inspections and cleanings since 2009, and Chimney Cap & Crown in Boulder issues are what we find most often on older masonry chimneys. The combination of Front Range temperature swings, intense UV at 5,400 feet, and the wet spring snow followed by dry winters creates a specific pattern of damage: concrete crowns crack, metal caps corrode at the seams, and flue gas exposure accelerates deterioration once the seal is broken. In neighborhoods like Mapleton Hill, Martin Acres, and the foothills above Chautauqua, we’ve documented crown failure rates significantly higher than the national average due to these exact conditions.

Emberly Chimney Cleaners Boulder operates under the Haven Standard, which means every cap and crown job starts with a camera-scan inspection down the flue, a written price and scope before anyone touches a tool, and a documented photo record stamped under Clause 4. Corrine Halstead built this practice into the company from day one. No verbal estimates. No surprises after the technician is already on your roof.

What Our Chimney Cap & Crown Service Includes

Cap Installation

A chimney cap is a metal cover that sits over your flue opening to block rain, snow, animals, and wind-blown debris while allowing smoke and combustion gases to escape. In Boulder, we install caps on chimneys that have never had one, typically in homes built before 1990 or where a previous cap was removed and never replaced. We measure your flue precisely, source the cap through Haven’s buying network from Copperfield or Gelco, and secure it with stainless steel fasteners rated for Colorado’s freeze-thaw cycles. Every installation includes a photo of the mounted cap from roof level and a close-up of the fastener pattern, both archived under Clause 4.

Cap Replacement

Cap replacement becomes necessary when the existing cap has rusted through, blown off in a wind event, or was improperly sized from the start. We see this frequently in Table Mesa and Newlands, where original caps were often galvanized steel that lasted 8-12 years instead of the 20+ years expected from stainless or copper. We remove the old cap, inspect the flue tile for damage that the leaking cap may have caused, and install a replacement with a proper overlap and screen mesh. The written price includes disposal of the old cap and a 365-Day Done Right Promise on the installation.

Crown Repair

The crown is the concrete slab that tops your masonry chimney, sloped to shed water away from the flue. Crown repair addresses cracks, spalling, or deterioration that has not yet compromised the structural integrity of the entire slab. In Boulder, we use HeatShield CrownSeal for minor cracks and localized spalling, or we remove and re-pour sections where the damage is deeper but the crown’s overall pitch and footprint remain sound. We never recommend a full rebuild when a targeted repair will last, and we document the before condition with photos you can see before approving any scope.

Crown Coating

Crown coating is a preventive or restorative application of flexible, waterproof sealant over an intact but weathered concrete crown. This is ideal for Boulder’s climate, where UV degradation and thermal expansion create hairline cracks that admit water before any structural damage is visible. We apply HeatShield CrownCoat or a comparable flexible membrane after wire-brushing the surface and masking the flue opening. The coating cures to a permeable finish that allows moisture vapor to escape while blocking liquid water. A typical coating extends crown life by 7-10 years and costs significantly less than rebuild.

Multi-Flue Cap

A multi-flue cap is a single cover that spans two or more flue openings on the same chimney, common in homes with both a fireplace and a furnace or water heater venting through the same structure. We measure the chimney top as a unit, accounting for the spacing and height differences between flues, and fabricate a cap from DuraFlex or Copperfield stock with a single integrated screen and lid system. This eliminates the gap between individual caps where water and animals enter, and it simplifies future maintenance. Multi-flue caps are particularly effective on Boulder’s larger historic homes in the University Hill and Whittier neighborhoods.

Custom Cap

Custom caps are fabricated when standard sizes won’t fit, when architectural review boards require specific materials or profiles, or when the homeowner wants a particular finish to match roof hardware. We’ve built custom copper caps for homes in Boulder Heights and custom black galvanized caps for modern builds in the Transit Village area. Every custom cap is drawn to specification, photographed during fabrication, and inspected on the roof before final fastening. The written price includes the drawing, material, and installation with no separate “design fee.”

Brands We Service for Chimney Cap & Crown

We source cap and crown materials through Haven’s buying network, which was built specifically to keep customer prices honest by eliminating distributor markups. For standard and multi-flue caps, we stock and install Copperfield and Gelco lines, both manufactured with 304 stainless steel as standard and optional copper or powder-coated finishes. We’ve installed hundreds of Copperfield single-flue caps on Boulder chimneys and keep their full size range in regional inventory, which means no waiting for freight from the East Coast. Gelco’s multi-flue systems are our default for larger masonry chimneys; their clamp-and-seal mounting hardware holds through Front Range wind events better than screw-through designs we’ve seen fail.

For crown repair and coating, we use HeatShield products exclusively. Their CrownSeal cementitious repair compound and CrownCoat flexible membrane are formulated for the thermal stress that destroys standard concrete patches in Colorado’s climate. We’ve applied HeatShield on more than 2,400 crowns since 2009 and track performance by address; the data shows 94% remain intact at five-year follow-up inspection. Whether your chimney currently has a Copperfield, Gelco, HeatShield, or any other make of cap or crown treatment, we can inspect it, repair it, or replace it with a documented record of what we found and what we did.

Before

After

Signs You Need Chimney Cap & Crown Right Now

• Water stains on the ceiling near your fireplace. This indicates the cap is missing, damaged, or improperly fitted, or the crown has cracked enough to allow water past the chimney’s protective layers. In Boulder’s spring snowmelt season, a single compromised entry point can saturate the masonry and damage interior framing within weeks.
• Rust stains running down the exterior brick from the chimney top. Rust means water is pooling on the crown or cap hardware is corroding, both of which signal that the metal components are failing and the concrete beneath is taking moisture. We’ve traced rust streaks back to flue liner collapse in homes near Baseline Reservoir where the cap had been gone for two unnoticed years.
• Debris, nesting material, or animal sounds in the flue. A missing or damaged cap is an open invitation to squirrels, raccoons, and starlings, all common in Boulder’s tree canopy. Nests block airflow, create fire hazards, and introduce moisture that accelerates liner deterioration. We remove the obstruction, inspect for damage, and install proper screening.
• Spalling or flaking concrete visible on the crown surface. Spalling occurs when water freezes in the concrete’s pore structure, expanding and breaking off surface layers. Boulder’s 50-degree temperature swings in March and November make this especially aggressive. Once spalling begins, the crown loses its slope and water begins ponding, which accelerates the cycle.
• White efflorescence staining on the chimney exterior below the roofline. Efflorescence is salt deposited by water moving through masonry and evaporating at the surface. It means water is entering the chimney system somewhere above, and the cap or crown is the most likely entry point. The salt itself is cosmetic, but the water movement it represents is degrading mortar joints and potentially reaching interior structures.

Our Chimney Cap & Crown Process - Step by Step

1. 1
   Schedule and confirm. Call (970) 598-0453 and speak with a live person, any hour. We assign a named technician, run a background check confirmation, and text you when they’re en route with an estimated arrival window. You’ll know who’s coming and when.
2. 2
   NFPA 211 Level 2 inspection with camera scan. Before touching the cap or crown, we run a video camera down the flue to document liner condition, creosote buildup, and any water damage that may have already occurred. This is Clause 4 of the Haven Standard, and the footage is yours to keep. We also photograph the crown and cap from roof level and from the ground for comparison.
3. 3
   Written diagnosis, price, and scope. We show you the camera footage and photos, explain what we found in plain terms, and deliver a written estimate with line-item pricing for each option: repair, coating, replacement, or rebuild. No work begins until you approve the scope in writing. This is Haven Standard Clause 1: Have it in writing.
4. 4
   Execution with photo documentation. Our technician completes the approved work using materials sourced from our Haven network. We photograph each stage: old cap removed, crown surface prepared, new cap mounted or coating applied, final fastener pattern. These images are archived with your job record and available on request.
5. 5
   Final inspection and warranty delivery. We verify the installation with a final camera run if the flue was accessed, confirm water shedding with a controlled spray test on crowns, and present your written warranty backed by the 365-Day Done Right Promise. If anything isn’t right, we make it right. Clause 5.

How Much Does Chimney Cap & Crown Cost in Boulder?

Chimney Cap & Crown Near Boulder - Our Service Area

We cover Boulder County and adjacent communities with cap and crown service, including Chimney Cap & Crown in Niwot, Chimney Cap & Crown in Louisville, and direct response to Lafayette, Erie, Broomfield, Longmont, Westminster, Frederick, Arvada, Thornton, and Wheat Ridge. Most Boulder city appointments are scheduled within 2-3 business days; foothills properties above 6,500 feet may require additional scheduling to accommodate weather windows. Our technicians are routed from a central dispatch and carry the full inventory of standard cap sizes, CrownSeal, and CrownCoat, so most jobs are completed in a single visit without a return trip for materials.

Frequently Asked Questions - Chimney Cap & Crown in Boulder

Schedule Your Chimney Cap & Crown Service in Boulder Today

Call (970) 598-0453 any time, day or night, and speak with a live person about your chimney cap or crown. We’ll assign a named, background-checked technician, run a camera down your flue, and deliver a written price before any work starts. Your estimate is free, your photo record is included, and your satisfaction is covered by the 365-Day Done Right Promise. No voicemail. No call for pricing. Just the inspection standard we built our name on.

Written by Corrine Halstead, Owner at Emberly Chimney Cleaners Boulder, serving Boulder, Niwot, Louisville, and surrounding communities since 2009.